Advanced Moisture Sensing + Steam. And if you have a blown thermal fuse or a defective lid or main control, replace it. As for getting out the plate, that was a challenge, bought some cheap picks from walmart, bent the J hook to match the L, stuck it in hole in plate on opposite sides, and popped that plate out. Heres how to check if it is faulty or not: The clutch connects the transmission and the inner tub. The stator works with the rotor to help the tub rotate. Due to the improper balance, the spin cycle of the washer will get affected. If there is no other issue in your washing machine that is causing a spinning malfunction, then it might be due to a damaged drive belt. High amounts of detergent can create too many suds. The rotor works in conjunction with the stator to make the drum spin. The motor control board supplies power to the motor. Specifically, check the windings in the stator to determine its state. These techniques will work on any Vertical Modular Washer like how to find error codes on a Washer. Check the Coupler Between the Agitator and Transmission. In fact, any washer will not drain or spin if the lid is not closed properly and the switch is activated. See the Installation Instructions for details; enter your product model number in the search tool below to find them online. Have you found yourself in a situation where your washer won't spin? Check if you have chosen the appropriate wash cycle for the type of material you are washing. Scott The Fix-It Guy ..DISCLAIMER: This video or description may contain Amazon affiliate links, which means that if you click on one of the product links and buy the product, Ill receive a small commission. A simple way to get your washer to spin would be to make sure you distribute the load evenly. Better yet, adjust each individual leg until the washer is perfectly level. May 25, 2018 by Wondering why is my Maytag Bravos washer not spinning even after these interventions? To make the bravos washer manufactured by Maytag drain properly when its lid switch is defective, try pressing the lid switch with your finger. Once you have access to the drive pulley, you need to check that the drive belt is going around it correctly and if the pulley is worn out or damaged. Used straps to get under the lip of the washplate to distribute effort. Use only HE High Efficiency detergent in this washer. If it is damaged, it will need to be replaced. A new washer would cost you anywhere from $500 for a basic top-loader to $1,500 for a high-end front-loader. If the drive pulley is defective, it will need to be replaced. The switch might need to be changed if nothing happens and testing with a multimeter reveals a lack of continuity. Do Not Overload the Machine Overloading a washing machine may cause an imbalance in the drum. Apply Now! Once found, close the lid and see if the lever on it activates the switch. Remove any blockage from the drain hose, drainpipe or utility sink. This unit will not also drain if the lid switch is defective. But, if the switch is faulty, it may prohibit these functions even if the lid is closed. However, if you need several parts, you might want to consider an agitator repair kit. You can reset your Bravos MCT Maytag washer in different ways. Thank you!!! 7MMPM0060VM1. Additionally, replace a faulty water level sensor, lid lock, inlet valve, or control board, Laundry overload, faulty lid, poor drainage, loose or defective drive belt, loose belts, or faulty water level switch, Reduce the excess load, replace the faulty lid lock, unclog the drains, replace the defective drive belt, tighten loose bolts or change the water level switch, Low water pressure or defective water inlet valve, Increase the water pressure (to 20 psi) and replace the water inlet valve if its faulty, A faulty lid switch, timer, cycle selector, drive motor, drive belt, or water level switch, Faulty door lock, water inlet valve, or main control, Power failure, poor drainage, unbalanced load, washer not level, or wrong spin selection, Fix the power issue, unclog the drains, balance the load, level the washer, and choose the right spin setting, Plug in your MCT washer but dont turn on the indicators (that puts the washer on standby mode), Rotate the cycle selector (main knob) clockwise thrice, Then turn it anticlockwise (once), then clockwise again (once), Wait for the indication to light up, indicating youve entered diagnostic mode. A bad bearing will cause the washer to spin extremely loudly or cause it to stop spinning altogether. How to Repair a Maytag Bravos Washing Machine That Does Not Agitate Properly - Drum Hub Replacement You will need a multimeter to check the wires for electrical activity. The parts generally are similar on non-VMW's too, but they're going to be located in different areas. There are several explanations for your Maytag Bravos washer which won't spin. Washer plate replacement (washer not washing) WHITE LIGHTNIN' 116K views 4 years ago Whirlpool Maytag washer drive block agitator. These tips can help prevent an unbalanced load or overloading: When the lid switch malfunctions, your washer wont drain or spin. A Maytag Bravos washer won't spin due to a wrong setting, poor drainage, unbalanced or overloaded load, power failure, or a defective lid switch. This guide covers most Maytag washer models, including: The lid switch assembly stops the washer from spinning when the lid is not closed properly. This would cost you anywhere from $40-$70. You will need to prepare a few things beforehand to make this task slightly less arduous and more time-efficient. Options. A kinked hose means erratic water flow that results in a. The rotor has several magnets on it that when damaged will stop the tub from spinning. Use the U-shaped drain hose form on the drain hose, and secure the drain hose. Error codes are either lid lock (which tests good) or balance issue (which is no longer the case since replacing spring rods.) If that still does not do the job, you may have a defective. The door latch makes sure the door on your Maytag washer stays closed when it is operating. Overall, all these problems have more than one probable cause, which Ill share with you. To find the problem and fix it, check each of the components listed below, and hopefully youll find out what is causing it. I live in Northern MI, and I'm a single, not so handy lady and repairman or handyman are a rare thing in our area. Closing the lid triggers a mechanism in the machine that signals it to start. The lid switch assembly prevents the washer from spinning when the lid is open. Removed hub, and visual inspection of old hub revealed exactly what you show here. Buyers beware!!! (All You Need to Know). Call Appliance Genie for fast, professional Maytag appliance repair service. If you find any part of the rotor is damaged or faulty, the whole unit will have to be replaced. How to manually drain Maytag bravos washer? This is very rarely the cause of washers not working, but it can happen. One common, but overlooked, cause could simply be jammed clothing or an uneven load. Replaced the hub, and washplate. If the lid is not properly closed, the washing machine will not drain and spin due to its safety features. To determine if the lid switch assembly is defective, use a multimeter to test the lid switch for continuity. If no power if reaching the drive motor, and the lid swith assembly or door latch test appropriately with a multimeter, then the timer is likely malfunctioning. /TM /*